Friday, May 29, 2009


This is all the cleaned parts. I had previously ordered a rebuild kit and Hey! All the parts fit! Hooray for me. The needle and seat were replaced, the main jet, the idle jet and all the gaskets and fuel filter were also replaced. The float was set to specs for drop (open) and lift (closed). The carb was then reassembled and the result is as shown above.

Is any one reading this stuff or am I just wasting my time??

While still waiting for parts for the other projects started and stalled, I decided to rebuild the carburetor as I felt it was possibly, slightly gummed up. Whaddya think? I was not even surprised when I removed the float bowl cover and found--guess! Yeah, more silicone from the previous moron-er, I mean mechanic. I spent most of the morning cleaning and blowing out jets and passages until I was sure it was a clean as it was gonna be.


Thursday, May 28, 2009



The first picture shows the tubes in place before tightening down the head. The next shows the head torqued to spec, the rocker shaft assembly installed and torqued and the tubes compressed to make a tight seal. I mentioned the fuel pump only had one seal but forgot to say the distributor had none. I also spent about 15-20 minutes digging silicone out of the block where the push rod tubes seat. I will probably have to wait until the engine is back in the car before I can remove the oil pan for cleaning and new gasket. For those not familiar with Fiat 500 engines the pan is double walled for cooling purposes. The blower fan is ducted through the space in the oil pan. I have looked in there and can see a whole bunch of wild cherry seeds, so I know it is going to take some serious probing and fishing to get them all out. When I get it off I'll post a picture showing the ducting through the bottom of the pan.


While waiting for parts for the timing chain that I was working on while waiting for parts for the differential I was working on, I started working on the rest of the engine. I cleaned the push rod tubes and stretched them to insure a tight seal when installed. This was accomplished by putting a real snug fitting socket in the end of the tube, clamping it in a vise, and pulling and wiggling it to lengthen the bellows. This was done to both ends. The seals were then put on making sure the beveled end faces away from the tube as shown in the picture to the left. The tubes were installed in the block using small amount of oil on the seals to ease them into their holes. The other picture shows them installed. The head gasket was installed over the head studs and the head was put on the studs and and allowed to settle to the tops of the tubes. After double checking that the tubes were straight in the holes, the head was tapped into place with a rubber mallet. The head nuts were placed on the studs making sure the capped nuts were under the valve cover and the open nuts on the outside of same. I think this is to prevent oil leaks from the rocker arm area down the head studs to the block. The nuts were then torqued to 24 ft. lbs. using the pattern shown in the shop manual. Although it wasn't specified, I did it in incremental steps until I reached 24 ft. lbs. The rocker arm shaft assembly was placed over its mounting studs and the nuts torqued to 14 ft. lbs. I also replaced a few gaskets while fooling around: the distributor gasket, both fuel pump gaskets---hmmm only had one gasket on it, surprise surprise.

Wednesday, May 27, 2009

This is a close up shot of the new driving sprocket and the mounting for the driven sprocket. I cleaned off the old gasket and the crud on the bottom, cleaned and made legible the engine number visible in the upper left corner. Now I'm reduced to waiting, because, yet AGAIN, I've received incorrect parts. The new large sprocket will not fit on the shaft without hitting the bolt heads on the round disk behind the smaller sprocket. Closer examination shows the teeth are not on the same plane as the old one, they sit too far back .I also discovered the new seal in the kit does not fit in the hole in the cover and the orientation of the sealing lips suggests that it is to be installed from the inside of the cover instead of the outside. Seems awfully weird to me. This shit is getting real, real old. Out of six orders, five have been wrong. Screw it! I'm going to bed.

You can see the timing chain and sprockets here. Notice there is no adjustment for taking up slack. If you click on the picture to enlarge it, you will see what looks like little tabs on each chain link. These are actually chain tighteners that work by centrifugal action. As they swing outward, they shorten each link a tiny bit, crude but effective. The other shot shows the chain and driven sprocket removed as described before. It is interesting to note that timing cannot be lost, the sprockets only fit one way. There is a line scribed on the smaller sprocket and a dot punched into a tooth on the larger one. They will line up when the sprockets are installed properly. If they don't line up the bolts won't fit since it is a staggered pattern.

The picture on the left shows the oil filter completely removed just before loosening the bolts to remove the cover. The right side shows the sediment trap after being cleaned. I then proceeded to remove the bolt locks and the bolts holding on the timing chain driven sprocket. The driving sprocket is a slip fit on a keyed shaft. These were removed and set aside. The cover was cleaned inside and out and set aside to dry.